VUT Harness & Electrical Parts

. One of those important and vital components on the SnowDogg VUT UTV Snow Plow is the plow electrical parts and harnesses. The electrical harness parts on the VUT UTV snow plow are made up of repair ends, grill connector caps, truck side control harnesses, controller for the plow itself, and more which are specific to the SnowDogg UTV V-Plow VUT65 snow plow.

  • SnowDogg Part # 16160512 – Harness Dust Cap for Lights

    0 out of 5

    SnowDogg Part # 16160512 – Harness Dust Cap for Lights SnowDogg harness cap covers the connector port which attaches to the lights on the side of the plow for your SnowDogg snow plow. This is a very common part and is used on almost all SnowDogg plows. You’ll find this dust cap on the plow side of your truck. Protect your wiring harness from corrosion and moisture from damaging the pins.

    $7.71
  • SnowDogg Part # 16160620 – Snow Plow Controller Dash Mount Kit

    0 out of 5

    SnowDogg Part # 16160620 – Snow Plow Controller Dash Mount Kit is used to mount your SnowDogg plow controller to your truck’s dashboard. You’ll receive the bracket itself, adhesive, and 4 screws for installation.

    $19.48
  • SnowDogg Part # 16160402 – Spring Cage Connector, Kit of 2

    0 out of 5

    SnowDogg Part # 16160402 – Spring Cage Connector, Kit of 2 are for your electrical components throughout your SnowDogg Plow. These are found on many of the SnowDogg plows including the XP series, CM plow, MD plows and more.

    $8.82
  • SnowDogg Part # 16160610 – Controller Extension Harness

    0 out of 5

    SnowDogg Part # 16160610 – Controller Extension Harness is used on SnowDogg plows such as the MD snow plow. This harness is an extension for your controller and is 36″ in length. You’ll notice the large white plugs at the end of each side of this harness. You’d plug this into your controller on one end, and the other end would plug to your main vehicle side control harness. This allows you to have a bit more wiggle room while plowing instead of being tied to a short cable.

    $25.70
  • SnowDogg Part # 16160300 – Truck Side Control Harness

    0 out of 5

    SnowDogg Part # 16160300 – Truck Side Control Harness is used on SnowDogg plows such as the XP, VXF, HD, EX, MD plows and more. Check your plow’s manual if you’re unsure if this is the harness you need. The control harness is located on the vehicle side of your plow setup. The end of the harness has a female end with (2) large pinholes and would come out the vehicle’s grille so you can plug and unplug as needed when you use your plow.

    $239.55
  • SnowDogg Part # 16160410 – HT300, HV600 HPU Relay Motor Power Unit Solenoid

    0 out of 5

    SnowDogg Part # 16160410 – HT300, HV600 HPU Relay Motor Power Unit Solenoid is used on all SnowDogg plow setups which have the HT300 or HV600 HPU hydraulic units such as the HD, EX, VX, and more. The relay motor solenoid is found on the vehicle side, most commonly under the hood near the battery on your truck. This is the solenoid which sends electrical current throughout your plow’s electrical system as needed. You’ll find wires such as positive, negative, and your control harness connected to this solenoid.

    $33.78
  • SnowDogg Part # 16160310 – Connector Repair Kit For Part # 16160300

    0 out of 5

    SnowDogg Part # 16160310 – Connector Repair Kit For Part # 16160300. This is the repair wiring connector for your SnowDogg 16160300. To install this connector repair kit, you’d remove the existing connector by cleanly cutting ghte harness before the damaged area. Strip the wires on the existing harness. And then properly crimp the wires using the butt connectors preinstalled on the repair harness.

    $140.41
  • SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU

    0 out of 5

    SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU is the plow side wiring which is plugged in at your plow motor. This harness is only used on the VXF series V plows. One end has a large plug which plugs into the vehicle side wiring, while the other end has power/ground, along with wires which plug to your valves and coils on the plow side.

    $123.04
  • SnowDogg Part # 16160320 – Control Connector Repair End for 16160300 Control

    0 out of 5

    SnowDogg Part # 16160320 – Control Connector Repair End for 16160300 Control Harness. If you have a 16160300 SnowDogg controller, this is the repair kit you’d need to fix any plug issues you may come across. This is a much cheaper option rather than replacing the entire controller harness.

    $31.00
  • SnowDogg Part # 16160630 – Snow Plow Controller Replacement Rubber Keypad

    0 out of 5

    SnowDogg Part # 16160630 – Snow Plow Controller Replacement Rubber Keypad is the button portion of your plow’s controller. This can become worn down over time or possible tear. If that happens, rather than replace the entire controller, buy a new rubber keypad and get it looking like brand new. 

    $22.13
  • SnowDogg Part # 16160404 – Small Spring Cage Connector

    0 out of 5

    SnowDogg Part # 16160404 – Small Spring Cage Connector is sold as “each” and used on many of the SnowDogg plows including the MD series, as well as the UTV MUT series straight blade plows. 

    $2.26
  • SnowDogg Part # 16161600 – VX V Plow Snow Plow Controller

    0 out of 5

    SnowDogg Part # 16161600 – VX V Plow Snow Plow Controller is used on the generation 1 v plows such as the SnowDogg VXF snow plows. This kit includes the v plow controller itself, wiring which comes out of the handle of the controller and goes to your main control wiring harness, as well as the mounting kit to mount this to your vehicle’s dashboard if needed. The cable coming from the controller is 24″ in length. Don’t buy an aftermarket plow controller. They don’t last nearly as long as an OEM controller like this.

    $283.34
You've just added this product to the cart: