SnowDogg Wiring Harness Parts including lighting harnesses, controller harnesses, and any other electrical wiring harness that makes up your SnowDogg Snow Plow can be bought directly from SnowplowsPlus in order to make your repair or upgrade to your plow and get you back on the road. You’ll get guaranteed OEM SnowDogg snow plow harness parts at the lowest prices around, as well as the largest selection, and you’ll them fast. SnowDogg Wiring parts will help you complete the connection between your plow truck and your SnowDogg plow itself in the form of wiring harnesses, cables, solenoids, and other electrical components.
SnowDogg Part # 16160512 – Harness Dust Cap for Lights$7.71
SnowDogg Part # 16160512 – Harness Dust Cap for Lights SnowDogg harness cap covers the connector port which attaches to the lights on the side of the plow for your SnowDogg snow plow. This is a very common part and is used on almost all SnowDogg plows. You’ll find this dust cap on the plow side of your truck. Protect your wiring harness from corrosion and moisture from damaging the pins.
SnowDogg Part # 16160510 – Wiring Harness Weather Protect Plug$7.71
SnowDogg Part # 16160510 – Wiring Harness Weather Protect Plug is used on SnowDogg plows to help protect your wiring harness from rain, sleet, and snow in order to help protect against corrosion and damage to your electrical components. This cap will work with wiring harnesses 16160100 and 16160300.
SnowDogg Part # 16160400 – Plow Side Control Harness$105.44
SnowDogg Part # 16160400 – Plow Control Harness is your controller wiring harness on the plow side of your setup. This is the harness which is connected to all of your HPU solenoid coils. One end of the wiring harness will have small coil plugs with different colored wires along with a positive and negative cable. The other side of the cable will have a large mail plug with (2) large pins on the bottom of the plug and smaller pins on the top. This is used on plows such as the SnowDogg EX, HD, TE, MD, and CM snow plows.
SnowDogg Part # 16160610 – Controller Extension Harness$25.70
SnowDogg Part # 16160610 – Controller Extension Harness is used on SnowDogg plows such as the MD snow plow. This harness is an extension for your controller and is 36″ in length. You’ll notice the large white plugs at the end of each side of this harness. You’d plug this into your controller on one end, and the other end would plug to your main vehicle side control harness. This allows you to have a bit more wiggle room while plowing instead of being tied to a short cable.
SnowDogg Part # 16160300 – Truck Side Control Harness$239.55
SnowDogg Part # 16160300 – Truck Side Control Harness is used on SnowDogg plows such as the XP, VXF, HD, EX, MD plows and more. Check your plow’s manual if you’re unsure if this is the harness you need. The control harness is located on the vehicle side of your plow setup. The end of the harness has a female end with (2) large pinholes and would come out the vehicle’s grille so you can plug and unplug as needed when you use your plow.
SnowDogg Part # 16160100 – Truck Light Relay Harness$244.17
SnowDogg Part # 16160100 – Truck Light Relay Harness is used on SnowDogg plows such as the SnowDogg MD, VMD, HD, EX, TE, XP ,VX, VXF, and CM snow plows. This is the harness which plugs into your vehicle’s lights, or headlight adapter, and has a large relay pack on it, and then exits through your vehicle’s grille. If you need individual relays for your existing harness, check out part number 16160114. This harness will include all new harness already connected on the relay block. This is an OEM part for SnowDogg plows only.
SnowDogg Part # 16160200 – Plow Side Light Harness$121.29
SnowDogg Part # 16160200 – Plow Light Harness is used on most all SnowDogg plows including the MD, VMD, HD, EX, TE, XP, VX, VXF, and CM snow plows. This is the harness located on the plow side. The light harness is plugged into each plow headlight assembly itself and comes together to one larger plug which plugs into the vehicle side relay harness. If you’re experiencing issues with your lights such as them not switching over to the plow or back to the truck successfully, this may be your issue. Check your wires for frays or cuts and repair as needed.
SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU$123.04
SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU is the plow side wiring which is plugged in at your plow motor. This harness is only used on the VXF series V plows. One end has a large plug which plugs into the vehicle side wiring, while the other end has power/ground, along with wires which plug to your valves and coils on the plow side.
SnowDogg Part # 16160116 – Relay Harness Mounting Plate$6.24
SnowDogg Part # 16160116 – Relay Harness Mounting Plate is used on all SnowDogg plow setups and located under the hood of your vehicle. On your main relay harness with the block of 6 relays, this is the mounting plate bracket which the relays are connected to so they stay in place and keep their connection to the wires plugged into their terminals.
SnowDogg Part # 16162400 – XP HPU Control Harness$122.90
SnowDogg Part # 16162400 – XP HPU Control Harness is only used on the SnowDogg XP810 snow plow with the hydraulic expandable wings. This harness has one end that has a plug with (2) large pins on the bottom and 7 plugs on the top. The other end of the harness has (7) smaller colored wires which attach to coils on your HPU on the plow side. The colors include blue, purple, green, orange, blue/white, green/white, and orange/white. This same side of the harness will also have positive and negative wires which go to your plow’s motor, along with (7) more smaller ground wires which go to all coils.
SnowDogg Part # 16071160 – Universal Headlight Adapter HB3, H11$102.28
SnowDogg Part # 16071160 – Universal Headlight Adapter HB3, H11 are used on vehicles such as the 2007-2013 Toyota Tundra and vehicles with HB3/HB11 headlights. Before purchasing or installation, check your truck’s headlight type. This adapter kit allows the truck’s lights to switch to the plow when in use and switch back to the vehicle when the plow is no longer in use for the night.
SnowDogg Part # 16073110 – H13 Splice in Connector Kit Harness$39.69
SnowDogg Part # 16073110 – H13 Splice in Connector Kit Harness requires the 16071100 headlight adapter kit if you are installing to your H13 headlights. This adapter kit may be used with switched ground vehicles. The BROWN wire for the PARK circuit on the 16071100 must be connected to GROUND, rather than a park light circuit and the relay harness must be configured as shown in the owner’s manual for switched ground installation