WELCOME TO SNOWPLOWSPLUS600DCKIT – Discontinued, Replaced by the New 6000DCKIT
$0.00The wireless remote controller conversion kit, 600DCKIT , is a single 12volt motor variable speed controller has 5 pre-set speeds in approx 1/5th increments. Comes with transmitter with glow in the dark label, rubber boot and lanyard. Receiver unit, 7 prong cord to plug into your truck receiver hitch and seal tight connectors. This unit is commonly used on single motor tailgate mounted salt sand spreaders such as Meyer, Western Low Profile, Boss TGS, SaltDogg Tailgate, Hiniker, Swenson and more. Completely replaces Meyer Part # 63930 Wireless Remote Control Kit and is hundreds of dollars cheaper! Most brands of vehicles have the battery charging pin of the 7-prong trailer plug-in activated. Many Chevrolet’s will not have the wire connected and or the fuse not installed for this function. The wire for this may be under the fuse box under the hood or taped to the wiring harness near the brake booster. Install this wire per mfg. instructions and install the proper fuse. If your vehicle is not equipped with the battery charging wire, you may add this by running a 8 or 10 gauge wire from the battery to the terminal on the truck side 7 prong plug as shown in the provided diagram. You must install a 40-amp fuse at the battery. Note 2015 and up Ford F150 and Ford 2017 and up F250,350 trucks do not have live power at the 7-prong trailer plug to operate a spreader, must use Anderson plug quick disconnect. If you do not have proper power and ground to the wireless unit it will not operate.
600DC1 – Discontinued, Replaced by the New 6000DCKIT
$0.00This 600DC1 Wireless transmitter controller and wireless receiver can be used as a replacement for any other wireless controllers built for the same on the market today including Meyer Part #63930, Fisher spreader wireless, Snow-Way, Snow-Ex, or any other brand on the market today. Most Make/Model of vehicles have the battery charging pin of the 7-prong trailer plug-in activated. Many Chevrolet’s will not have the wire connected and or the fuse not installed for this function. The wire for this may be under the fuse box under the hood or taped to the wiring harness near the brake booster. Install this wire per mfg. instructions and install the proper fuse. If your vehicle is not equipped with the battery charging wire, you may add this by running a 8 or 10 gauge wire from the battery to the terminal on the truck side 7 prong plug as shown in the provided diagram. You must install a 40-amp fuse at the battery. Note 2015 and up Ford F150 and Ford 2017 and up F250,350 trucks do not have live power at the 7-prong trailer plug to operate a spreader, must use Anderson plug quick disconnect. If you do not have proper power and ground to the wireless unit it will not operate. 95% of failures are on the truck side and or failed 7 prong connections, always verify power to the unit as a first step in diagnosing a problem. Simply remove the cover from the receiver unit and press the black button. If the red light blinks you have power to the unit if not it is on the truck-side.
625DC – Universal Salt Spreader Wireless Controller Single DC Electric – 1 Extra Function (Vibrate, Aux, Etc)
$419.00Take your salt spreader to the next level.
The 625DC is a universal salt spreader wireless conversion kit for single motor variable speed control with an extra latching on/off function to operate another apparatus such as vibrate, light, or any aux function. Comes with 24′ power ground wiring, dust caps, sealtite connectors quick connect Anderson plugs and complete instructions. This is the only wireless controller kit on the market for those of you with a salt spreader which is powered by a single DC electric motor.
Our Wireless Controller works on both tailgate spreaders as well as Hopper Box spreaders. Functions found on the wireless controller include 3 variable speeds, power on and off, and auxiliary functions which can control your vibrator (if you have one), aux lights or any other accessory you may have which requires 12V power (If no accessory, you’d simply not use that wire/function when installing). Super easy to install and they will last longer than your OEM wired spreader assembly. Be sure to check out our wireless controller for gas spreaders, as well as our dual motor spreader wireless controller kits if you don’t have a single DC electric spreader.
NOTE: This is not the entire kit. You need power/ground harness from truck battery to back of truck, anderson plugs, and connectors for wiring. We sell the 625DCKIT which comes with everything you need to make the switch. This wireless controller setup is for those that would rather buy their wiring and connectors elsewhere or already have them.
650DCKIT – DISCONTINUED – REPLACED BY THE 6500DCKIT
$623.20The 650DCKIT is a universal dual motor variable speed wireless transmitter controller with wireless receiver and everything you need to completely convert to a wireless connection to your salt spreader. The 650DCKIT will operate 2 12 volt DC motors up to 1/2hp each. 3 pre-set speeds per motor. Comes with 24′ power/ground cord with Anderson quick connect plugs and dust caps, seal tite connectors and complete instructions. Commonly used on dual electric motor salt sand spreaders from Boss, Western,Fisher, SaltDogg, Meyer, Hiniker, Swenson, Monroe, Henderson, Downeaster, and more.
650DC – DISCONTINUED – REPLACED BY THE 6500DCKIT
$0.00The 650DC is a universal dual motor variable speed wireless transmitter controller with wireless receiver for a complete wireless connection to your salt spreader from up to 100ft away. The 650DC will operate 2 12 volt DC motors up to 1/2hp each. 3 pre-set speeds per motor. Sold separately are the 24′ power/ground cord with Anderson quick connect plugs and dust caps, seal tite connectors and can also be purchased all in a complete conversion kit, 650DCKIT. Commonly used on dual electric motor salt sand spreaders from Boss, Western,Fisher, SaltDogg, Meyer, Hiniker, Swenson, Monroe, Henderson, Downeaster, and more.
625DCKIT – Universal Salt Spreader Wireless Remote Controller Conversion Kit Single DC Electric – 1 Extra Function (Vibrate, Aux, Etc)
$612.80Take your salt spreader to the next level.
The 625DC KIT is a universal salt spreader wireless conversion kit for single motor variable speed control with an extra latching on/off function to operate another apparatus such as vibrate, light, or any aux function. Comes with 24′ power ground wiring, dust caps, sealtite connectors quick connect Anderson plugs and complete instructions. This is the only wireless controller kit on the market for those of you with a salt spreader which is powered by a single DC electric motor.
Our Wireless Controller works on both tailgate spreaders as well as Hopper Box spreaders. Functions found on the wireless controller include 3 variable speeds, power on and off, and auxiliary functions which can control your vibrator (if you have one), aux lights or any other accessory you may have which requires 12V power (If no accessory, you’d simply not use that wire/function when installing). Super easy to install and they will last longer than your OEM wired spreader assembly. Be sure to check out our wireless controller for gas spreaders, as well as our dual motor spreader wireless controller kits if you don’t have a single DC electric spreader. If you’d rather buy this salt spreader wireless controller without the plugs and wires, while providing these on your end to complete installation, we sell this same kit with just the transmitter and receiver.
Extreme Hose Part # E-16153100 – EXTREME HOSE REPLACES SNOWDOGG..16153100
$21.00Extreme Hose Part # E-16153100 – EXTREME HOSE REPLACES SNOWDOGG..16153100
SnowDogg Part # 16065115HDW – MD Plow Mount Hardware Kit for Toyota Tundra 2000-2006
$21.56SnowDogg Part # 16065115HDW – MD Plow Mount Hardware Kit for Toyota Tundra 2000-2006. This kit is for the hardware parts needed to install your plow mount to your vehicle. You only need this if you are replacing existing bolts, nuts and washers or if you are installing an old mount on a new truck. This kit includes parts such as nuts, bolts and washers and will not include any mount parts including bars, side plates or brackets.
Part # 0208000A – AUGER ASSEMBLY TGS01, TGSUVPRO SERIES
$94.34Part # 0208000A – AUGER ASSEMBLY TGS01, TGSUVPRO SERIES
Part # 0091610HDW – HARDWARE, JACK, REPLACEMENT (0091610)
$14.04Part # 0091610HDW – HARDWARE, JACK, REPLACEMENT (0091610)
