Buy all of your SnowDogg SKTE Plow Parts from SnowplowsPlus to guarantee the replacement parts you receive are 100% OEM. We have the entire replacement parts makeup of the SnowDogg SKTE snow plows including the blade itself, hydraulic parts, electric parts, wiring parts, controller parts, hardware parts and more. SnowDogg SKTE snow plow parts have never been easier to buy and get shipped fast to your door with SnowplowsPlus and are easy to sort SnowDogg SKTE plow parts categories broken down by each component including moldboard, HPU, Lift Frame, Accessories, Service Parts, Electrical Parts, and more. When you buy from us, you not only get the largest selection of instock SnowDogg SKTE Plow Parts, but you get the fastest shipping around and a knowledgeable staff that can help you out along the way.
SKTE Hardware Kit
SKTE Moldboard Plow Parts
SKTE Mount & A-Frame Parts
SnowDogg SKTE Common Parts
SnowDogg Part # 16121120 – MD, HD, EX, VX, CM Snowplow Plow Shoe Washer (1 Per)
SnowDogg Part # 16121120 WASHER, PLOW SHOE, MD/HD/EX/VX/CM
SnowDogg Part # 16153110 – Hydraulic Angle Hose 3/8 x 36
SnowDogg Part # 16153110 – Hydraulic Angle Hose 3/8 x 36 is used on MD, HD, and EX straight blade plows. This hose is an OEM hydraulic hose from SnowDogg is 36″ long and has 3/8″ port ends. This is the hose which allows your plow to angle left and right as you press the buttons on your plow’s controller.
SnowDogg Part # 16154212 – Packing Kit 1-1/2 in. w/Wiper Seal
SnowDogg Part # 16154212 – Packing Kit 1-1/2 in. w/Wiper Seal is the angle pack kit for your SnowDogg MD snow plow. If you own a SnowDogg MD plow and have a leaky or faulty hydraulic angle cylinder, you may want to try this packing kit before purchasing an all new angle cylinder.
SnowDogg Part # 16101200 – OEM Trip Spring
SnowDogg Part # 16101200 – Replacement Trip Spring is found on the back of your plow’s blade and used on all SnowDogg plows, both Gen 1 and Gen 2. Most SnowDogg plows will require at least 4 of these springs which run the length of your plow’s moldboard frame. These trip springs are what allow your plow to easily maneuver through any hidden obstacles without damaging your plow or truck due to excessive force.
SnowDogg Part # 16122100 – Blade Guide Kit Pair
SnowDogg Part # 16122100 – Blade Guide Kit Pair is used on SnowDogg plows such as the MD, HD, EX plows and more. These are OEM and are the original blade guides found on your SnowDogg plow when it rolled off the lot. These are orange in color and you’ll receive (2) blade guide poles, and the hardware needed to install onto your plow.
SnowDogg Part # 16121158 – MD75 Formed Poly Snow Deflector
SnowDogg Part # 16121158 – MD75 Formed Poly Snow Deflector. This is the plastic poly snow deflector which is installed on the top of your plow’s blade to help keep the snow from blowing over the plow and into your truck’s windshield.
SnowDogg Part # 16120114 – Cutting Edge Fastener Kit Set of 10
SnowDogg Part # 16120114 HDW KIT, CUTTING EDGE,
SnowDogg Part # 16102142 – Clevis Pin Kit With Hardware 7/8 x 3-1/4 in.
SnowDogg Part # 16102142 – Clevis Pin Kit With Hardware 7/8 x 3-1/4 in. is found on plows such as the SnowDogg HD/EX plows, MD, VX/VXF, VMD, TE, XP, and Skid Steer plows. This pin is used on your chain lift assembly to hold the chin in place to the plow’s frame.
SnowDogg Part # 16151324 – HT300 Manifold Angle Port Fitting
SnowDogg Part # 16151324 – HT300 Manifold Angle Port Fitting is used on all SnowDogg plows with the HT300 HPU hydraulic units. There are (2) of these used on the Hydraulic Manifold assembly, with both on the side wall towards the bottom of the sidewall itself.
SnowDogg Part # 16121700 – VXF, VX, VMD, TE Heavy Duty Plow Shoe Assembly
SnowDogg Part # 16121700 – VXF, VX, VMD, TE Heavy Duty Plow Shoe Assembly is used on the plow blade frame to help raise the plow up slightly if you have loose ground that needs snow cleared from it. This allows your plow to skim the top while clearing all the snow, but leaves the ground in place without disturbing the loose material underneath. This is for (1) single shoe assembly with hardware. If you need to replace or buy both sides, you’ll need to buy (2) of these kits.
SnowDogg Part # 16120156 – HD75, EX75 Formed Poly Snow Deflector
SnowDogg Part # 16120156 – HD75, EX75 Formed Poly Snow Deflector is the plastic poly portion installed on the top of your plow blade. This is only used on the SnowDogg HD75 and SnowDogg EX75 7.5 ft. straight blade plows. This pre-formed snow deflector helps keep the snow down, forcing it out on th edges of your plow rather than up and into your truck’s windshield. If your deflector has become damaged, get it replaced right away or you’ll be fighting with trying to see what’s in front of you.
SnowDogg Part # 16120162 – EX90 Formed Poly Snow Deflector
SnowDogg Part # 16120162 – EX90 Formed Poly Snow Deflector is found on the SnowDogg EX90 and EXII90 generation 1 and generation 2 plows. This is the formed poly snow deflector installed on the top of your plow blade to help keep the snow down and from blowing over the top of your plow into your truck’s windshield. SnowDogg also makes a rubber deflector for the EX90 which we also sell.