Snowplowsplus has the largest selection of instock SnowDogg controller parts including remote controllers for SnowDogg XP810, V-plow, straight blade plows, and UTV snow plows. When it comes to SnowDogg by Buyers, we have it all. Mount that controller to your dashboard with the SnowDogg Control dashboard kit. Replace your controller wire, or the entire remote if needed. Check out all of our controller products for SnowDogg snow plows. If you’re looking to take your SnowDogg Controller to the next level, head on over to our wireless plow controllers. SnowplowsPlus has the only SnowDogg wireless controller on the market. The cost of our wireless SnowDogg controller kit is half the cost of having to buy a new OEM SnowDogg control, control wiring harnesses, and the rest of the parts needed to complete that original connection.
SnowDogg Part # 16160400 – Plow Side Control Harness
SnowDogg Part # 16160400 – Plow Control Harness is your controller wiring harness on the plow side of your setup. This is the harness which is connected to all of your HPU solenoid coils. One end of the wiring harness will have small coil plugs with different colored wires along with a positive and negative cable. The other side of the cable will have a large mail plug with (2) large pins on the bottom of the plug and smaller pins on the top. This is used on plows such as the SnowDogg EX, HD, TE, MD, and CM snow plows.
SnowDogg Part # 16160300 – Truck Side Control Harness
SnowDogg Part # 16160300 – Truck Side Control Harness is used on SnowDogg plows such as the XP, VXF, HD, EX, MD plows and more. Check your plow’s manual if you’re unsure if this is the harness you need. The control harness is located on the vehicle side of your plow setup. The end of the harness has a female end with (2) large pinholes and would come out the vehicle’s grille so you can plug and unplug as needed when you use your plow.
SnowDogg Part # 16160610 – Controller Extension Harness
SnowDogg Part # 16160610 – Controller Extension Harness is used on SnowDogg plows such as the MD snow plow. This harness is an extension for your controller and is 36″ in length. You’ll notice the large white plugs at the end of each side of this harness. You’d plug this into your controller on one end, and the other end would plug to your main vehicle side control harness. This allows you to have a bit more wiggle room while plowing instead of being tied to a short cable.
SnowDogg Part # 16160600 – MD, EX, HD Snow Plow Controller
SnowDogg Part # 16160600 – MD, EX, HD Snow Plow Controller is the straight blade controller found on generation 1 SnowDogg straight blade snow plows. This is an OEM straight blade controller and used on SnowDogg plows such as the SnowDogg MD, HD, EX, and TE snow plows. Controller is pre-programmed specifically for use with straight blades. This controller comes with the controller wiring which is 24″ long and comes directly out of the handheld controller itself before it plugs into your main controller harness on the truck. You’ll also receive the controller mounting bracket for installation.
SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU
SnowDogg Part # 16161400B – V-Plow VX Control Harness Complete HPU is the plow side wiring which is plugged in at your plow motor. This harness is only used on the VXF series V plows. One end has a large plug which plugs into the vehicle side wiring, while the other end has power/ground, along with wires which plug to your valves and coils on the plow side.
SnowDogg Part # 16160320 – Control Connector Repair End for 16160300 Control
SnowDogg Part # 16160320 – Control Connector Repair End for 16160300 Control Harness. If you have a 16160300 SnowDogg controller, this is the repair kit you’d need to fix any plug issues you may come across. This is a much cheaper option rather than replacing the entire controller harness.
SnowDogg Part # 16160630 – Snow Plow Controller Replacement Rubber Keypad
SnowDogg Part # 16160630 – Snow Plow Controller Replacement Rubber Keypad is the button portion of your plow’s controller. This can become worn down over time or possible tear. If that happens, rather than replace the entire controller, buy a new rubber keypad and get it looking like brand new.
SnowDogg Part # 16160370 – Old Controller to New Controller Harness Adapter
SnowDogg Part # 16160370 – Old Controller to New Controller Harness Adapter. If you have the older controller wiring harness but a new gen 2 controller, this is the adapter you’d need to install your new controller without having to buy all new wiring throughout your vehicle.
SnowDogg Part # 16161600 – VX V Plow Snow Plow Controller
SnowDogg Part # 16161600 – VX V Plow Snow Plow Controller is used on the generation 1 v plows such as the SnowDogg VXF snow plows. This kit includes the v plow controller itself, wiring which comes out of the handle of the controller and goes to your main control wiring harness, as well as the mounting kit to mount this to your vehicle’s dashboard if needed. The cable coming from the controller is 24″ in length. Don’t buy an aftermarket plow controller. They don’t last nearly as long as an OEM controller like this.
SnowDogg Part # 16161601A – V-Plow VX Plow Controller Gen-2 2018 Version
SnowDogg Part # 16161601A – V-Plow VX Plow Controller Gen-2 2018 Version. This is only for the newer Gen2 Plows. If the front of your V-Plow says “VXII” on it, this is the controller you need. This OEM SnowDogg V Plow controller includes the mounting bracket needed, as well as hardware for installation. The new and improved handheld controller is easy to use and allows you to control all functions of your plow including float mode, scoop mode, v mode, and many more.
SnowDogg Part # 16160601A – Straight Blade Plow Controller Gen 2 2018 Version
SnowDogg Part # 16160601A – Straight Blade Plow Controller Gen 2 2018 Version is used on the newer HD and EX plows. This is only used for the generation 2 plows. If your plow blade says “EXII” or “HDII” on it, this is the controller you need. You’ll also receive the mounting bracket and hardware for installation.
SnowDogg Part # 3039788 – V-Plow Switch Option Upgrade
SnowDogg Part # 3039788 – V-Plow Switch Option Upgrade is specifically for the SnowDogg V Plow Gen2 upgrade and will include the jack switch kit as well as the updated controller for your v-plow.