HD/EX HPU Parts

The SnowDogg HD/EX Snow Plow is made up of a few vital components that ensure your snow removal experience is smooth with maximum performance. One of those important and vital components on the SnowDogg HD/EX is the HPU, or the “brains of the plow”. The HPU of the HD/EX snow plow is made up of the HPU itself, reservoir, seal kit, motor, and more which are specific to the SnowDogg HD/EX snow plow.

  • SnowDogg Part # 16151318 – HT300 10V SA, SB, SC Coil Valves

    0 out of 5

    SnowDogg Part # 16151318 – HT300 10V SA, SB, SC Coil Valve is a coil for your HT300 HPU found on most SnowDogg Plows. This is one of the coils you’d find on your HPU itself with blue, black, orange, and green wires coming off of them. This is only for (1) coil.

    Earn 2.74 Reward Points
    $27.43
  • SnowDogg Part # 16151102 – HT300, HV600 Inlet Strainer With Elbow

    0 out of 5

    SnowDogg Part # 16151102 – HT300, HV600 Inlet Strainer With Elbow is found on all SnowDogg plows with the HT300 or HV600 HPU hydraulic units. Just about every SnowDogg plow will have this inlet strainer kit. This inlet strainer with elbow is located within the hydraulic reservoir assembly and is directly attached to the plow pump.

    Earn 1.22 Reward Points
    $12.24
  • SnowDogg Part # 16159102 – Seal Kit For Part # 16151312, and 16151330

    0 out of 5

    SnowDogg Part # 16159102 – Seal Kit For Part # 16151312, and 16151330 is found on Gen 1 and Gen 2 SnowDogg plows. This is the seal kit for your 16151312 and 16151330 solenoid valves.

    Earn 1.53 Reward Points
    $15.30
  • SnowDogg Part # 16151312 – HT300 SA Solenoid Drop Valve

    0 out of 5

    SnowDogg Part # 16151312 – HT300 SA Solenoid Drop Valve is used on generation 1 and generation 2 SnowDogg plows. The SA valve is located on your HPU on the hydraulic manifold assembly. If you’re looking at the side of the manifold, the SA valve is the one at the end, closest to your relief valves. The SA valve is connected to the SA coil which has two wires connected to it’s posts including the black cross over wire which goes to SB and the Blue wire. If you’re having issues with your plow dropping or in float mode, this is a good place to start troubleshooting.

    Earn 6.63 Reward Points
    $66.30
  • SnowDogg Part # 16151110 – HT300, HV600 Reservoir Kit

    0 out of 5

    SnowDogg Part # 16151110 – HT300, HV600 Reservoir Kit is used on most all SnowDogg plows from the HD to the VMD and everything in between. Check your HPU’s model number. If it’s HT300 or HV600, this is the reservoir you need. The kit includes the reservoir, o-ring, and hardware needed to install. Don’t make the mistake of buying an aftermarket Reservoir for your SnowDogg plow like the majority of the other sites out there. We’ll get you OEM parts every time.

    Earn 7.65 Reward Points
    $76.50
  • SnowDogg Part # 16151321 – 90 Degree Swivel Manifold Lift Fitting

    0 out of 5

    SnowDogg Part # 16151321 – 90 Degree Swivel Manifold Lift Fitting is found on the SnowDogg VMD75 plow. This is located on the HPU itself and on the hydraulic manifold assembly. Specifically, the swivel is attached to the cylinder lift port fitting which is attached to the side wall of your manifold assembly.

    Earn 1.43 Reward Points
    $14.28
  • SnowDogg Part # 16159114 – HT300 Reservoir Seal Kit

    0 out of 5

    SnowDogg Part # 16159114 – HT300 Reservoir Seal Kit is found on all HT300 reservoirs within your SnowDogg’s HPU. This is the large seal kit which is located at the “bottom” of the reservoir between the reservoir and the manifold assembly.

    Earn 1.02 Reward Points
    $10.20
  • SnowDogg Part # 16159106 – Seal Kit For Part # 16151316

    0 out of 5

    SnowDogg Part # 16159106 – Seal Kit For Part # 16151316 and used on both the newer generation 2 plows like the SnowDogg HDII, EXII and TEII, as well as the 1st generation SnowDogg plows. This is the seal kit for your 16151316 solenoid 4-way reversing valves found on the hydraulic manifold unit within your HPU.

    Earn 1.84 Reward Points
    $18.36
  • SnowDogg Part # 16159104 – Seal Kit for 16151314 Lift/Angle Valve

    0 out of 5

    SnowDogg Part # 16159104 – Seal Kit for 16151314 Lift/Angle Valve and used on both the newer generation 2 plows like the SnowDogg HDII, EXII and TEII, as well as the 1st generation SnowDogg plows. This is the seal kit for your 16151314 solenoid valve 3-way selector, located on the hydraulic manifold unit within your HPU.

    Earn 1.53 Reward Points
    $15.30
  • SnowDogg Part # 16151316 – HT300 SC Left and Right Valve

    0 out of 5

    SnowDogg Part # 16151316 – HT300 SC Left and Right Valve is used on both the generation 1 and gen 2 plows from SnowDogg. This OEM hydraulic valve allows your plow to move left and right after you press the corresponding button on your plow’s controller. If your plow won’t move left or right, this is one of the first things to check and replace.

    Earn 8.16 Reward Points
    $81.60
  • SnowDogg Part # 16151302 – HT300 Main Relief Valve

    0 out of 5

    SnowDogg Part # 16151302 – HT300 Main Relief Valve is used on most SnowDogg plows including the HD, EX, MD, CM plows and more. This is the main relief valve found on the hydraulic manifold block. Specifically, this valve is located on the side of the manifold in between the angle port fitting and lift port fitting.

    Earn 3.72 Reward Points
    $37.21
  • SnowDogg Part # 16151314 – HT300 SB Lift and Angle Valve

    0 out of 5

    SnowDogg Part # 16151314 – HT300 SB Lift and Angle Valve is used on both the Generation 1 and Gen 2 SnowDogg plows. This is the lift and angle valve on your HPU and is the middle valve when looking at the side of the manifold. This valve connects to the SB coil, which plugs into the green wire as well as a cross wire coming from the SC coil and valve. This is only for the SB hydraulic valve itself. If you are experiencing issues with your plow related to the actual lifting of the blade or angle actions, you may need this valve.

    Earn 8.16 Reward Points
    $81.60
You've just added this product to the cart: